High speed motor stator Coil Powder Coating Machine power tool coil
winding insulation WIND-SCPC Photo under production:
Coil powder coating purpose:
For the power tool, usually it works with high speed, during long
time operation, the dust can go to coil surface,
If no power tool insulaiton, the surface will be covered by the
dust which will contain copper,metal, then there will be a short,
coil power coating can avoid the short,it is widely used for famous
customer such as Black&Decker
|Powder coating method||Short circuit heat the winding coil and dip to fluid bed not
|Stator powder coating application||High speed motor power tool coil winding powder coating insulation|
1.For 2 poles commutator motor stator power coating
2. The machine has count function.
3. Working hours can be decided by customer.
4. Machine working ability 120~180pcs/h
(1) Coil powder coating machine: 1set, including:
1.1 Machine mainframe 1set
Outline dimension:L1253×W1300(include powder cleaning room 500mm)
The room body manufactured by 1.2mm A3 cold rolled plate.
1.2 DC electrical heating device: 1set
Heating power(0~10KW, clearance working way)adjustable,it can set
1.3 Pneumatic rise and decline device 1 set
1.4 Fluidized bed coating device: 1set
All PVC plate manufacture, with detachable air chamber and
1.5 .Powder vibration device 1set
1.6. First step pulse recycling in the back 1set, with 2pcs filter
element and pulse auto back flushingfunction, it can clean the
powder in the filter element automatically without turning off the
machine, with 1 set powder-blowing gun.
1.7 The coating room doorway install photo-electricity
protection(raster)device, this keep the user saver when operating.
1.8 The machine has count function.
(1) Powder secondary recycling machine(outline dimension
L830×W830×H1700mm): 1 set
(2) Use 25 type pulse back flushing filter element way recycling
machine, motor power 2.2KW.
Design and produce principle
Motor stator coil
Stator lamination diameter<Φ95mm
stator lamination thickness(includecoil height)<100mm Max
<3 Kg Max/pc
This output means the machine working ability;
it depends on the powder characteristic.
Decide by customer
(1) Load the coil (1pc) to the sling fitting and insert each wire
head(heated) into the connection groove, compact inching cylinder.
(2)Turn on the switch (go up and down, heating, coating etc
controlled by time relay to work automatically)
(3) After finish coating (the powder adhere to the stator coil and
through melting and leveling preliminary, there's a little powder
in the inside and outside of the stator lamination, but not melt,
it can clean completely by preliminary air blowing and subsequent
cleaning).Take it down and transmit toanother person, clean the
inside and outside of the stator with air blowing gun in the powder
cleaning entrance, then put it on the shelf (prepared by customer)
for natural cooling → put into oven together for baking (prepared
by customer, the bake requirement of the powder in the oven is the
oven temperature rise to the needed temperature for curing
powder(this depend on the enameled wire heat- resisting temperature
and powder curing requirement), keep hot insulation for over 40
(1)Electricity: 380V±10%, 50HZ. Electricity supply way: three phase
four wire system.
(2)Compressed air: 0.6Mpa containing oil:≤0.1ppm containing water:
This Coil Powder Coating Machine is used for stator coil powder
The machine has count function.Working hours can be decied by
Machine working ability 120~180pcs/h
Contact: Shanghai Wind Automation Equipment Co.,Ltd
Website: http://www.motor-machinery.com; http://www.coilswinding.com